Transverters for microwaves are a very common accessory. However, with factory radios, the displayed frequency usually does not match the one you are working on, and you have to recalculate it in your head. Dawid, SQ6EMM, decided not to wait for Icom and prepared his own firmware for IC-705 and IC-9700.
The first version was published on November 11, 2026 on the Polish forum Mikrofale.cafe, and since then there have been more than seventy contributions and several editions. I have summarized what the firmware knows today, what has been verified by users and where the limits are.
You will read in the article
Transverters and tuning
The basis is the native support of transverters: eight memories TRV1 to TRV8, display of frequencies up to 122 GHz, setting of maximum power, TX delay and PTT blocking. You can find the function in MENU, SET, Transverter. One forum user commented that he never understood why Icom didn't add a simple conversion for transverters.
On the IC-9700 there is a separate setting for both MAIN and SUB and it also works in satellite mode, as confirmed by SP1JMF. SQ1GQC verified the TX delay with an oscilloscope. It is measured from the moment the key contacts stop vibrating, so when keying shorter than the set delay, the time is reduced. The author promised the requirement to limit power for transverters (maximum 5% and minimum 1%) in the next version.
Decoders and custom applications
The biggest news came on November 18. Q65-60D, FT8, JT4G, PI4 and WSPR decoders were added to the radio. You copy the APP files from the .zip archive to the SD card in the Apps subfolder, restart the radio and select the application in the MENU, SET, APPS menu. Then on the VFO screen you open the modulation mode selection and repeatedly press RTTY to switch between modes.
It also includes ICAP SDK pre vývojárov vlastných aplikácií. G7LWT s jeho pomocou vytvoril jednoduchý APRS a demo program that, according to him, worked the first time. The author of the firmware announced that APRS and D-PRS integration is under testing. Decoder CW však zatiaľ nepríde: zdroje rádií Icom sú podľa neho veľmi obmedzené a niečo ako deepCW exceeds the capabilities of the hardware. One user also reported that when running for a long time on VHF the FT8 or APRS decoder stopped decoding after a while.
70 MHz and ranges: reality
The firmware for the IC-705 unlocks the transmitter even on 70 MHz without opening the radio. However, the firmware alone is not enough, the band must be calibrated in the service menu. The author has published a procedure with values, but warns that they may be specific to his piece. Users report mixed results: some have TX activated but no output power.
According to the author, reception of 200 to 400 MHz is not possible because it is a matter of hardware. SQ6QV added that the input stage bandpass filters and oscillator lowpass filters would need to be changed. The Japanese version of the IC-705 has a different band structure in the code. It is reported to unblock reception around 300 kHz to 199 MHz and 400 to 470 MHz, but broadcasting is limited to 144 to 146 MHz. The author did not prepare the latest issue from November 18 for this version, because it requires more work and he does not own it.
Bootloader A/B: attention to detail
The radio holds two firmwares and you can switch. However, the procedure turned out to be more complicated than the README describes. With IC-705, according to SP3RNY, the selection (three LED flashes) can only be triggered when powered from the battery, with an external source, the last used version is always started. SQ1SDX recommends disconnecting both external power and USB and holding POWER until the radio starts up. For the IC-9700, turn off both the radio and power, wait about 30 seconds, hold down POWER, apply power and hold until the radio starts up, then turn it off and on again. TRV settings will be preserved after reloading.
Don't forget the risks either: the bootloader is overwritten once during the update from the SD card, and a power failure at that moment may require a Flash programmer. The author himself admits that during development, the AI tools caused him problems several times, which required a physical flash upload.
CI-V and control programs
Frequencies selected in TRV are also returned by CI-V, which the author tried with Hamlib under Linux. On Windows, the situation remained unclear: SQ1SDX reported that HRD and WSJT-X did not work for him in the first versions, and PA5DJ pointed out that the frequency setting in TRV via CI-V on the IC-705 does not work yet.
Web patcher and liability
Dawid only distributes patches. You can download the original .dat file from Icom and web patcher it edits it directly in the browser, with MD5 check, and offers the result only if it matches the tested assembly. The code is on GitHub licensed by MIT, see the discussion at Mikrovale.cafe. Experience adds up quickly, so check the patcher page for the current version before uploading.
Pay attention to the legal side: extended ranges extend beyond the amateur bands and you can only broadcast where your license allows. The firmware is not from Icom, use it at your own risk and may void your warranty. BI1BIF is also conducting independent research on the Japanese version of the IC-705.
Frequently asked questions
For which radios is the firmware intended?
For Icom IC-705 and IC-9700, for IC-705 also in Japanese version. The latest November 18 release is for the European versions of the IC-705 and IC-9700 so far.
What decoders does the firmware include?
Q65-60D, FT8, JT4G, PI4 and WSPR which are activated by APP files on SD card. According to the author, the CW decoder exceeds the capabilities of the hardware.
Is it possible to receive 200 to 400 MHz on the IC-705?
No, the author called it a hardware limitation. Input stage bandpass filters and oscillator filters interfere.
How do I go back to the previous firmware?
Via A/B bootloader, but the procedure varies by radio and power supply. For the IC-705, the battery must be used for selection, and for the IC-9700, proceed as described above.
Does CI-V work with hamlib, HRD and WSJT-X?
The author tested it with hamlib under Linux. With HRD and WSJT-X, users reported problems in the first versions, and the frequency setting in TRV via CI-V does not work yet.
